Skip to content

AVD example for a single data center using L3LS

Introduction

This example is meant to be used as the logical second step in introducing AVD to new users, directly following the Introduction to Ansible and AVD section. The idea is that new users with access to virtual switches (using Arista vEOS-lab or cEOS) can learn how to generate configuration and documentation for a complete fabric environment. Users with access to physical switches will have to adapt a few settings. This is all documented inline in the comments included in the YAML files. If a lab with virtual or physical switches is not accessible, this example can also be used to only generate the output from AVD if required.

The example includes and describes all the AVD files and their content used to build an L3LS EVPN/VXLAN Symmetric IRB network covering a single DC, using the following:

  • Two (virtual) spine switches.
  • Two sets of (virtual) leaf switches, serving endpoints such as servers.
  • Two (virtual) layer2-only switches often used for management connectivity to the servers.

Integration with CloudVision is not included in this example to keep everything as simple as possible. In this case, the Ansible host will communicate directly with the switches using eAPI.

Installation

Requirements to use this example:

  • Follow the installation guide for AVD found here.
  • Run the following playbook to copy the examples to your current working directory, for example ansible-avd-examples:

ansible-playbook arista.avd.install_examples

This will show the following:

 ~/ansible-avd-examples# ansible-playbook arista.avd.install_examples

PLAY [Install Examples]***************************************************************************************************************************************************************************************************************************************************************

TASK [Copy all examples to ~/ansible-avd-examples]*****************************************************************************************************************************************************
changed: [localhost]

PLAY RECAP
****************************************************************************************************************************************************************************************************************************************************************************
localhost                  : ok=1    changed=1    unreachable=0    failed=0    skipped=0    rescued=0    ignored=0

After the playbook has run successfully, the directory structure will look as shown below, the contents of which will be covered in later sections:

ansible-avd-examples/ (or wherever the playbook was run)
  |── single-dc-l3ls
    ├── ansible.cfg
    ├── documentation
    ├── group_vars
    ├── images
    ├── intended
    ├── inventory.yml
    ├── playbook.yml
    ├── README.md
    └── switch-basic-configurations

Info

If the content of any file is modified and the playbook is rerun, the file will not be overwritten. However, if any file in the example is deleted and the playbook is rerun, Ansible will re-create the file.

Overall design overview

Physical topology

The drawing below shows the physical topology used in this example. The interface assignment shown here are referenced across the entire example, so keep that in mind if this example must be adapted to a different topology. Finally, the Ansible host is connected to the dedicated out-of-band management port (Ethernet0 when using vEOS-lab):

Figure: Arista Leaf Spine physical topology

IP ranges used

Out-of-band management IP allocation for DC1 172.16.1.0/24
Default gateway 172.16.1.1
dc1-spine1 172.16.1.11
dc1-spine2 172.16.1.12
dc1-leaf1a 172.16.1.101
dc1-leaf1b 172.16.1.102
dc1-leaf2a 172.16.1.103
dc1-leaf2b 172.16.1.104
dc1-leaf1c 172.16.1.151
dc1-leaf2c 172.16.1.152
Point-to-point links between leaf and spine (Underlay)
DC1 10.255.255.0/26
Loopback0 interfaces used for EVPN peering 10.255.0.0/27
Loopback1 interfaces used for VTEP (Leaf switches)
DC1 10.255.1.0/27
VTEP Loopbacks used for diagnostics (Leaf switches)
VRF10 10.255.10.0/27
VRF11 10.255.11.0/27
SVIs (interface vlan…) 10.10.<VLAN-ID>.0/24
For example interface VLAN11 has the IP address: 10.10.11.1
MLAG Peer-link (interface vlan 4094) (Leaf switches)
DC1 10.255.1.64/27
MLAG iBGP Peering (interface vlan 4093) (Leaf switches)
DC1 10.255.1.96/27

BGP design

Figure: Arista Underlay BGP Design

Figure: Arista Underlay BGP Design

Basic EOS config

Basic connectivity between the Ansible host and the switches must be established before Ansible can be used to push configurations. You must configure the following on all switches:

  • A hostname configured purely for ease of understanding.
  • An IP enabled interface - in this example the dedicated out-of-band management interface is used.
  • A username and password with the proper access privileges.

Below is the basic configuration file for dc1-leaf1a:

dc1-leaf1a-basic-configuration.txt
! ansible-avd-examples/single-dc-l3ls/switch-basic-configurations/dc1-leaf1a-basic-configuration.txt
! Basic EOS config
!
! Hostname of the device
hostname dc1-leaf1a
!
! Configures username and password for the ansible user
username ansible privilege 15 role network-admin secret sha512 $6$7u4j1rkb3VELgcZE$EJt2Qff8kd/TapRoci0XaIZsL4tFzgq1YZBLD9c6f/knXzvcYY0NcMKndZeCv0T268knGKhOEwZAxqKjlMm920
!
! Defines the VRF for MGMT
vrf instance MGMT
!
! Defines the settings for the Management1 interface through which Ansible reaches the device
interface Management1
   description oob_management
   no shutdown
   vrf MGMT
   ! IP address - must be set uniquely per device
   ip address 172.16.1.101/24
!
! Static default route for VRF MGMT
ip route vrf MGMT 0.0.0.0/0 172.16.1.1
!
! Enables API access in VRF MGMT
management api http-commands
   protocol https
   no shutdown
   !
   vrf MGMT
      no shutdown
!
end
!
! Save configuration to flash
copy running-config startup-config

Note

The folder single-dc-l3ls/switch-basic-configurations/ contains a file per device for the initial configurations.

Ansible inventory, group vars and naming scheme

The following drawing shows a graphic overview of the Ansible inventory, group variables, and naming scheme used in this example:

Figure: Ansible inventory and vars

Note

The two servers dc1-leaf1-server1 and dc1-leaf2-server1 at the bottom are not configured by AVD, but the switch ports used to connect to the servers are.

Group names use uppercase and underscore syntax:

  • FABRIC
  • DC1
  • DC1_SPINES
  • DC1_L3_LEAVES
  • DC1_L2_LEAVES

All hostnames use lowercase and dashes, for example:

  • dc1-spine1
  • dc1-leaf1a
  • dc1-leaf2c

The drawing also shows the relationships between groups and their children:

  • For example, dc1-spine1 and dc1-spine2 are both children of the group called DC1_SPINES.

Additionally, groups themselves can be children of another group, for example:

  • DC1_L3_LEAVES is a group consisting of the groups DC1_LEAF1 and DC1_LEAF2
  • DC1_L3_LEAVES is also a child of the group DC1.

This naming convention makes it possible to extend anything easily, but as always, this can be changed based on your preferences. Just ensure that the names of all groups and hosts are unique.

Content of the inventory.yml file

This section describes the entire ansible-avd-examples/single-dc-l3ls/inventory.yml file used to represent the above topology.

It is important that the hostnames specified in the inventory exist either in DNS or in the hosts file on your Ansible host to allow successful name lookup and be able to reach the switches directly. A successful ping from the Ansible host to each inventory host verifies name resolution(e.g., ping dc1-spine1).

Alternatively, if there is no DNS available, or if devices need to be reached using a fully qualified domain name (FQDN), define ansible_host to be an IP address or FQDN for each device - see below for an example:

inventory.yml
---
all:
  children:
    FABRIC:
      children:
        DC1:
          children:
            DC1_SPINES:
              hosts:
                dc1-spine1:
                  ansible_host: 172.16.1.11
                dc1-spine2:
                  ansible_host: 172.16.1.12
            DC1_L3_LEAVES:
              hosts:
                dc1-leaf1a:
                  ansible_host: 172.16.1.101
                dc1-leaf1b:
                  ansible_host: 172.16.1.102
                dc1-leaf2a:
                  ansible_host: 172.16.1.103
                dc1-leaf2b:
                  ansible_host: 172.16.1.104
            DC1_L2_LEAVES:
              hosts:
                dc1-leaf1c:
                  ansible_host: 172.16.1.151
                dc1-leaf2c:
                  ansible_host: 172.16.1.152

        NETWORK_SERVICES:
          children:
            DC1_L3_LEAVES:
            DC1_L2_LEAVES:
        CONNECTED_ENDPOINTS:
          children:
            DC1_L3_LEAVES:
            DC1_L2_LEAVES:

The above is what is included in this example, purely to make it as simple as possible to get started. However, in the future, please do not carry over this practice to a production environment, where an inventory file for an identical topology should look as follows when using DNS:

inventory.yml
---
all:
  children:
    FABRIC:
      children:
        DC1:
          children:
            DC1_SPINES:
              hosts:
                dc1-spine1:
                dc1-spine2:
            DC1_L3_LEAVES:
              hosts:
                dc1-leaf1a:
                dc1-leaf1b:
                dc1-leaf2a:
                dc1-leaf2b:
            DC1_L2_LEAVES:
              hosts:
                dc1-leaf1c:
                dc1-leaf2c:

        NETWORK_SERVICES: # (1)!
          children:
            DC1_L3_LEAVES:
            DC1_L2_LEAVES:
        CONNECTED_ENDPOINTS: # (2)!
          children:
            DC1_L3_LEAVES:
            DC1_L2_LEAVES:
  1. NETWORK_SERVICES

    - Creates a group named NETWORK_SERVICES. Ansible variable resolution resolves this group name to the identically named group_vars file (ansible-avd-examples/single-dc-l3ls/group_vars/NETWORK_SERVICES.yml).

    - The file’s contents, which in this case are specifications of VRFs and VLANs, are then applied to the group’s children. In this case, the two groups DC1_L3_LEAVES and DC1_L2_LEAVES.

  2. CONNECTED_ENDPOINTS

    - Creates a group named CONNECTED_ENDPOINTS. Ansible variable resolution resolves this group name to the identically named group_vars file (ansible-avd-examples/single-dc-l3ls/group_vars/CONNECTED_ENDPOINTS.yml).

    - The file’s contents, which in this case are specifications of connected endpoints (typically servers), are then applied to the children of the group, in this case, the two groups DC1_L3_LEAVES and DC1_L2_LEAVES.

Defining device types

Since this example covers building an L3LS network, AVD must know about the device types, for example, spines, L3 leaves, L2 leaves, etc. The devices are already grouped in the inventory, so the device types are specified in the group variable files with the following names and content:

---
type: spine
---
type: l3leaf
---
type: l2leaf

For example, all switches that are children of the DC1_SPINES group defined in the inventory will be of type spine.

Setting fabric-wide configuration parameters

The ansible-avd-examples/single-dc-l3ls/group_vars/FABRIC.yml file defines generic settings that apply to all children of the FABRIC group as specified in the inventory described earlier.

The first section defines how the Ansible host connects to the devices:

FABRIC.yml
ansible_connection: ansible.netcommon.httpapi # (1)!
ansible_network_os: arista.eos.eos # (2)!
ansible_user: ansible # (3)!
ansible_password: ansible
ansible_become: true
ansible_become_method: enable # (4)!
ansible_httpapi_use_ssl: true # (5)!
ansible_httpapi_validate_certs: false # (6)!
  1. The Ansible host must use eAPI
  2. Network OS which in this case is Arista EOS
  3. The username/password combo
  4. How to escalate privileges to get write access
  5. Use SSL
  6. Do not validate SSL certificates

The following section specifies variables that generate configuration to be applied to all devices in the fabric:

FABRIC.yml
fabric_name: FABRIC # (1)!

underlay_routing_protocol: EBGP
overlay_routing_protocol: EBGP

local_users: # (2)!
  ansible:
    privilege: 15
    role: network-admin
    sha512_password: $6$7u4j1rkb3VELgcZE$EJt2Qff8kd/TapRoci0XaIZsL4tFzgq1YZBLD9c6f/knXzvcYY0NcMKndZeCv0T268knGKhOEwZAxqKjlMm920
  admin:
    privilege: 15
    role: network-admin
    no_password: true

bgp_peer_groups: # (3)!
  evpn_overlay_peers:
    password: Q4fqtbqcZ7oQuKfuWtNGRQ==
  ipv4_underlay_peers:
    password: 7x4B4rnJhZB438m9+BrBfQ==
  mlag_ipv4_underlay_peer:
    password: 4b21pAdCvWeAqpcKDFMdWw==

p2p_uplinks_mtu: 1500 # (4)!
  1. The name of the fabric for internal AVD use. This name must match the name of an Ansible Group (and therefore a corresponding group_vars file) covering all network devices.
  2. Local users/passwords and their privilege levels. In this case, the ansible user is set with the password ansible and an admin user is set with no password.
  3. BGP peer groups and their passwords (all passwords are “arista”).
  4. Point-to-point interface MTU, in this case, is set to 1500 since the example uses vEOS, but when using hardware, this should be set to 9214 instead.

Setting device specific configuration parameters

The ansible-avd-examples/single-dc-l3ls/group_vars/DC1.yml file defines settings that apply to all children of the DC1 group as specified in the inventory described earlier. However, this time the settings defined are no longer fabric-wide but are limited to DC1. In this example, this is of limited benefit with only a single data center. Still, it allows us to scale the configuration to a scenario with multiple data centers in the future.

DC1.yml
---
mgmt_gateway: 172.16.1.1 # (1)!

spine:
  defaults:
    platform: vEOS-lab # (2)!
    loopback_ipv4_pool: 10.255.0.0/27 # (3)!
    bgp_as: 65100 # (4)!
    bgp_defaults: # (5)!
      - no bgp default ipv4-unicast
      - distance bgp 20 200 200
      - graceful-restart restart-time 300
      - graceful-restart

  nodes: # (6)!
    dc1-spine1:
      id: 1 # (7)!
      mgmt_ip: 172.16.1.11/24 # (8)!

    dc1-spine2:
      id: 2
      mgmt_ip: 172.16.1.12/24
  1. The default gateway for the management interface of all devices in DC1 is defined.
  2. platform references default settings defined in AVD specific to certain switch platforms.
  3. loopback_ipv4_pool defines the IP scope from which AVD assigns IPv4 addresses for Loopback0.
  4. bgp_as defines the BGP AS number.
  5. bgp_defaults defines generic BGP settings.
  6. nodes defines the actual spine switches, using the hostnames defined in the inventory.
  7. id is used to calculate the various IP addresses, for example, the IPv4 address for the Loopback0 interface. In this case, dc1-spine1 will get the IPv4 address 10.255.0.1/27 assigned to the Loopback0 interface.
  8. mgmt_ip defines the IPv4 address of the management interface. As stated earlier, Ansible will perform name lookups using the hostnames specified in the inventory unless using the ansible_host option. However, there is no automatic mechanism to grab the result of the name lookup and use that to generate the management interface configuration.

The following section covers the L3 leaf switches. Significantly more settings need to be set compared to the spine switches:

DC1.yml
l3leaf:
  defaults:
    platform: vEOS-lab # (1)!
    loopback_ipv4_pool: 10.255.0.0/27 # (2)!
    loopback_ipv4_offset: 2 # (3)!
    vtep_loopback_ipv4_pool: 10.255.1.0/27 # (4)!
    uplink_interfaces: ['Ethernet1', 'Ethernet2'] # (5)!
    uplink_switches: ['dc1-spine1', 'dc1-spine2'] # (6)!
    uplink_ipv4_pool: 10.255.255.0/26 # (7)!
    mlag_interfaces: ['Ethernet3', 'Ethernet4'] # (8)!
    mlag_peer_ipv4_pool: 10.255.1.64/27 # (9)!
    mlag_peer_l3_ipv4_pool: 10.255.1.96/27 # (10)!
    bgp_defaults:
      - no bgp default ipv4-unicast
      - distance bgp 20 200 200
      - graceful-restart restart-time 300
      - graceful-restart
    virtual_router_mac_address: 00:1c:73:00:00:99 # (11)!
    spanning_tree_priority: 4096 # (12)!
    spanning_tree_mode: mstp # (13)!

  node_groups: # (14)!
    DC1_L3_LEAF1:
      bgp_as: 65101 # (15)!
      nodes:
        dc1-leaf1a:
          id: 1
          mgmt_ip: 172.16.1.101/24
          uplink_switch_interfaces: # (16)!
            - Ethernet1
            - Ethernet1
        dc1-leaf1b:
          id: 2
          mgmt_ip: 172.16.1.102/24
          uplink_switch_interfaces:
            - Ethernet2
            - Ethernet2

    DC1_L3_LEAF2:
      bgp_as: 65102
      nodes:
        dc1-leaf2a:
          id: 3
          mgmt_ip: 172.16.1.103/24
          uplink_switch_interfaces:
            - Ethernet3
            - Ethernet3
        dc1-leaf2b:
          id: 4
          mgmt_ip: 172.16.1.104/24
          uplink_switch_interfaces:
            - Ethernet4
            - Ethernet4
  1. platform references default settings defined in AVD specific to certain switch platforms.
  2. loopback_ipv4_pool defines the IP scope from which AVD assigns IPv4 addresses for Loopback0. Please note that this IP pool is identical to the one used for the spine switches in this example. To avoid setting the same IP addresses for several devices, we define the option loopback_ipv4_offset.
  3. loopback_ipv4_offset offsets all assigned loopback IP addresses counting from the beginning of the IP scope. This is required when the same IP pool is used for two different node_types (like spine and l3leaf in this example) to avoid overlapping IPs. The offset is “2” in this case because each spine switch uses one loopback address.
  4. vtep_loopback_ipv4_pool defines the IP scope from which AVD assigns IPv4 addresses for the VTEP (Loopback1).
  5. uplink_interfaces defines the interfaces used locally on the leaf switches.
  6. uplink_switches defines the uplink switches, which are dc1-spine1 and dc1-spine2. Note that the uplink_interfaces and uplink_switches are paired vertically.
  7. uplink_ipv4_pool defines the IP scope from which AVD assigns IPv4 addresses for the uplink interfaces that were just defined.
  8. mlag_interfaces defines the MLAG interfaces used on each leaf switch, in this case, Ethernet3 and Ethernet4. These two interfaces will form PortChannel3 used for the MLAG peer link. Note that PortChannel3 is selected since the first interface is Ethernet3.
  9. mlag_peer_ipv4_pool defines the IP scope from which AVD assigns IPv4 addresses for the MLAG peer link interface VLAN4094.
  10. mlag_peer_l3_ipv4_pool defines the IP scope from which AVD assigns IPv4 addresses for the iBGP peering established between the two leaf switches via the SVI/IRB interface VLAN4093.
  11. virtual_router_mac_address defines the MAC address used for the anycast gateway on the various subnets. This is the MAC address connected endpoints will learn when ARPing for their default gateway.
  12. spanning_tree_priority sets the spanning tree priority. Since spanning tree in an L3LS network is effectively only running locally on the switch, the same priority across all L3 leaf switches can be re-used.
  13. spanning_tree_mode defines the spanning tree mode. In this case, we are using MSTP, which is the default. However, other modes are supported should they be required, for example, for connectivity to legacy or third-party vendor environments.
  14. node_groups defines settings common to more than one node. For example, for leaf switches, when exactly two nodes are part of a node group, AVD will, by default, automatically generate MLAG configuration.
  15. bgp_as is defined once since an MLAG pair shares a single BGP AS number.
  16. uplink_switch_interfaces defines the interfaces used on the uplink switches (Ethernet1 on dc1-spine1 and dc1-spine2 in this example). Defining which spine interfaces the leaf is connected to under the leaf switch settings makes adding and removing leaf switches much easier. There is no need to add/remove any settings under the spine switch section; AVD takes care of that for you. This child device/parent device hierarchy also applies to L2 and L3 leaves.

Finally, more of the same, but this time for the L2 leaf switches:

DC1.yml
l2leaf:
  defaults:
    platform: vEOS-lab
    uplink_interfaces: ['Ethernet1', 'Ethernet2']
    spanning_tree_mode: mstp

  node_groups:
    DC1_L2_LEAF1:
      uplink_switches: ['dc1-leaf1a', 'dc1-leaf1b']
      nodes:
        dc1-leaf1c:
          id: 1
          mgmt_ip: 172.16.1.151/24
          uplink_switch_interfaces:
            - Ethernet8
            - Ethernet8

    DC1_L2_LEAF2:
      uplink_switches: ['dc1-leaf2a', 'dc1-leaf2b']
      nodes:
        dc1-leaf2c:
          id: 2
          mgmt_ip: 172.16.1.152/24
          uplink_switch_interfaces:
            - Ethernet8
            - Ethernet8

As should be clear, an L2 leaf switch is much simpler than an L3 switch. Hence there are fewer settings to define.

Specifying network services (VRFs and VLANs) in the EVPN/VXLAN fabric

NETWORK_SERVICES.yml
---
tenants:
  # Definition of tenants. Additional level of abstraction to VRFs
  TENANT1:
    # Number used to generate the VNI of each VLAN by adding the VLAN number in this tenant.
    mac_vrf_vni_base: 10000
    vrfs:
      # VRF definitions inside the tenant.
      VRF10:
        # VRF VNI definition.
        vrf_vni: 10
        # Enable VTEP Network diagnostics
        # This will create a loopback with virtual source-nat enable to perform diagnostics from the switch.
        vtep_diagnostic:
          # Loopback interface number
          loopback: 10
          # Loopback ip range, a unique ip is derived from this ranged and assigned
          # to each l3 leaf based on it's unique id.
          loopback_ip_range: 10.255.10.0/27
        svis:
          # SVI definitions.
          "11":
            # SVI Description
            name: VRF10_VLAN11
            enabled: true
            # IP anycast gateway to be used in the SVI in every leaf.
            ip_address_virtual: 10.10.11.1/24
          "12":
            name: VRF10_VLAN12
            enabled: true
            ip_address_virtual: 10.10.12.1/24
      VRF11:
        vrf_vni: 11
        vtep_diagnostic:
          loopback: 11
          loopback_ip_range: 10.255.11.0/27
        svis:
          "21":
            name: VRF11_VLAN21
            enabled: true
            ip_address_virtual: 10.10.21.1/24
          "22":
            name: VRF11_VLAN22
            enabled: true
            ip_address_virtual: 10.10.22.1/24

    l2vlans:
      # These are pure L2 vlans. They do not have a SVI defined in the l3leafs and they will be bridged inside the VXLAN fabric
      "3401":
        name: L2_VLAN3401
      "3402":
        name: L2_VLAN3402

All VRF and VLANs are defined here. This means that regardless of where a given VRF or VLAN must exist, its existence is defined in this file, but it does not indicate where in the fabric it exists. That was done at the bottom of the inventory file previously described in the Inventory section.

AVD offers granular control of where Tenants and VLANs are configured using tags and filter. Those areas are not covered in this basic example.

A single tenant called TENANT1 is specified. The first setting is the base number (10000) used to generate the L2VNI numbers automatically, L2VNI = base number + VLAN-id. For example, L2VNI for VLAN11 = 10000 + 11 = 10011.

Next, two VRFs are defined, each with two VLANs. For example:

NETWORK_SERVICES.yml
      VRF10:
        vrf_vni: 10
        vtep_diagnostic:
          loopback: 10
          loopback_ip_range: 10.255.10.0/27
        svis:
          "11":
            name: VRF10_VLAN11
            enabled: true
            ip_address_virtual: 10.10.11.1/24
          "12":
            name: VRF10_VLAN12
            enabled: true
            ip_address_virtual: 10.10.12.1/24

This defines VRF10, with an L3VNI of 10 and two VLANs (VLAN11 and VLAN12). Each VLAN has a name and a virtual IP address, which will be used as the default gateway for that particular VLAN on all leaf switches where the VLAN is created.

The following configuration is also defined under VRF10:

NETWORK_SERVICES.yml
        vtep_diagnostic:
          loopback: 10
          loopback_ip_range: 10.255.10.0/27

This enables more user-friendly diagnostics for troubleshooting purposes by defining a specific loopback per VRF. This will create the following Arista EOS config. For example, on dc1-leaf1a:

interface Loopback10
   description VRF10_VTEP_DIAGNOSTICS
   no shutdown
   vrf VRF10
   ip address 10.255.10.3/32
!
ip address virtual source-nat vrf VRF10 address 10.255.10.3

At the bottom of the NETWORK_SERVICES.yml file, two layer2-only VLANs (VLAN3401 and VLAN3402) are defined. These VLANs are only bridged across the fabric but never routed anywhere:

NETWORK_SERVICES.yml
    l2vlans:
      "3401":
        name: L2_VLAN3401
      "3402":
        name: L2_VLAN3402

Specifying endpoint connectivity in the EVPN/VXLAN fabric

After the previous section, all VRFs and VLANs across the fabric are now defined. The ansible-avd-examples/single-dc-l3ls/group_vars/CONNECTED_ENDPOINTS.yml file specifies the connectivity for all endpoints in the fabric (typically servers):

CONNECTED_ENDPOINTS.yml
---
# Definition of connected endpoints in the fabric.
servers:
  # Name of the defined server.
  dc1-leaf1-server1:
    # Definition of adapters on the server.
    adapters:
    - type: server
      # Name of the server interfaces that will be used in the description of each interface
      server_ports: [ PCI1, PCI2 ]
      # Device ports where the server_ports are connected.
      switch_ports: [ Ethernet5, Ethernet5 ]
      # Device names where the server_ports are connected.
      switches: [ dc1-leaf1a, dc1-leaf1b ]
      # VLANs that will be configured on these ports.
      vlans: 11-12,21-22
      # Native VLAN to be used on these ports.
      native_vlan: 4092
      # L2 mode of the port.
      mode: trunk
      # Spanning tree portfast configuration on this port.
      spanning_tree_portfast: edge
      # Definition of the pair of ports as port channel.
      port_channel:
        # Description of the port channel interface.
        description: PortChannel dc1-leaf1-server1
        # Port channel mode for LACP.
        mode: active

    - type: ilo
      server_ports: [ iLO ]
      switch_ports: [ Ethernet5 ]
      switches: [ dc1-leaf1c ]
      vlans: 11
      mode: access
      spanning_tree_portfast: edge

  dc1-leaf2-server1:
    adapters:
    - type: server
      server_ports: [ PCI1, PCI2 ]
      switch_ports: [ Ethernet5, Ethernet5 ]
      switches: [ dc1-leaf2a, dc1-leaf2b ]
      vlans: 11-12,21-22
      native_vlan: 4092
      mode: trunk
      spanning_tree_portfast: edge
      port_channel:
        description: PortChannel dc1-leaf2-server1
        mode: active

    - type: ilo
      server_ports: [ iLO ]
      switch_ports: [ Ethernet5 ]
      switches: [ dc1-leaf2c ]
      vlans: 11
      mode: access
      spanning_tree_portfast: edge

This defines the settings for the relevant switch ports to which the endpoints connect, in this case the two servers dc1-leaf1-server1 and dc1-leaf2-server1.

As an example, here is the configuration for dc1-leaf1-server1:

CONNECTED_ENDPOINTS.yml
  dc1-leaf1-server1:
    adapters: # (1)!
    - type: server
      server_ports: [ PCI1, PCI2 ] # (2)!
      switch_ports: [ Ethernet5, Ethernet5 ] # (3)!
      switches: [ dc1-leaf1a, dc1-leaf1b ] # (4)!
      vlans: 11-12,21-22 # (5)!
      native_vlan: 4092 # (6)!
      mode: trunk # (7)!
      spanning_tree_portfast: edge # (8)!
      port_channel: # (9)!
        description: PortChannel dc1-leaf1-server1
        mode: active

    - type: ilo
      server_ports: [ iLO ]
      switch_ports: [ Ethernet5 ]
      switches: [ dc1-leaf1c ]
      vlans: 11
      mode: access
      spanning_tree_portfast: edge
  1. The relevant adapters are defined. The type set to server and ilo is purely for documentation and readability purposes. It has no operational significance.
  2. server_ports are defined for use in the interface descriptions on the switch. This does not configure anything on the server.
  3. switch_ports defines the interfaces used in the switches. In this example the server is dual-connected to Ethernet5 and Ethernet5. These two ports exist on switch dc1-leaf1a and dc1-leaf1b defined in the following line.
  4. switches defines the switches used, in this case dc1-leaf1a and dc1-leaf1b. Note that the server_ports, switch_ports and switches definitions are paired vertically.
  5. vlans defines which VLANs are allowed on the switch_ports, in this case it is two ranges, VLAN11-12 and VLAN21-22 for the dual-attached server ports and VLAN11 for the iLO port.
  6. native_vlan specifies the native VLAN when the switch port mode is set to trunk.
  7. mode is set to trunk for the dual-attached server ports and access for the iLO port.
  8. spanning_tree_portfast defines whether the switch port should be a spanning tree edge port or a network port.
  9. port-channel defines the description and mode for the port-channel.

The playbook

In this example, the playbook looks like the following:

playbook.yml
---
# Please note, comments below are intended for site documentation only
- name: Run AVD # (1)!
  hosts: FABRIC
  gather_facts: false
  tasks:
    - name: Generate AVD Structured Configurations and Fabric Documentation # (2)!
      import_role:
        name: arista.avd.eos_designs
    - name: Generate Device Configurations and Documentation # (3)!
      import_role:
        name: arista.avd.eos_cli_config_gen
    - name: Deploy Configurations to Devices # (4)!
      import_role:
        name: arista.avd.eos_config_deploy_eapi
  1. At the highest level, the name and scope of the playbook is set, which in this example is the entire fabric. For instance, FABRIC is a group name defined in the inventory. If the playbook should only apply to a subset of devices, it can be changed here.
  2. This task uses the role arista.avd.eos_designs, which generates structured configuration for each device. This structured configuration can be found in the ansible-avd-examples/single-dc-l3ls/intended/structured_configs folder.
  3. This task uses the role arista.avd.eos_cli_config_gen, which generates the actual Arista EOS CLI configurations found in the ansible-avd-examples/single-dc-l3ls/intended/configs folder, along with the device-specific and fabric wide documentation found in the ansible-avd-examples/single-dc-l3ls/documentation/ folder. It relies on the structured configuration generated by arista.avd.eos_designs.
  4. This task uses the role arista.avd.eos_config_deploy_eapi that pushes the generated configuration to the devices in scope.

Testing AVD output without a lab

Example of using this playbook without devices (local tasks):

playbook.yml
- name: Run AVD
  hosts: FABRIC
  gather_facts: false
  tasks:
    - name: generate intended variables
      import_role:
        name: arista.avd.eos_designs
    - name: generate device intended config and documentation
      import_role:
        name: arista.avd.eos_cli_config_gen
    # - name: deploy configuration to device
    #   import_role:
    #      name: arista.avd.eos_config_deploy_eapi

By simply commenting out (or deleting) the last task definition, the playbook will generate all of the output (variables, configurations, documentation), but will not attempt to communicate with any devices.

Please look through the folders and files described above to learn more about the output generated by AVD.

Executing the playbook

The execution of the playbook should produce the following output:

user@ubuntu:~/Documents/git_projects/ansible-avd-examples/single-dc-l3ls$ ansible-playbook playbook.yml

PLAY [Run AVD] *****************************************************************************************************************************************************************************

TASK [arista.avd.eos_designs : Collection arista.avd version 3.5.0 loaded from /home/user/.ansible/collections/ansible_collections] ******************************************************
ok: [dc1-leaf1a]

TASK [arista.avd.eos_designs : Create required output directories if not present] **********************************************************************************************************
ok: [dc1-leaf1a -> localhost] => (item=/home/user/Documents/git_projects/ansible-avd-examples/single-dc-l3ls/intended/structured_configs)
ok: [dc1-leaf1a -> localhost] => (item=/home/user/Documents/git_projects/ansible-avd-examples/single-dc-l3ls/documentation/fabric)
(...)

If similar output is not shown, make sure:

  1. The documented requirements are met.
  2. The latest arista.avd collection is installed.

Troubleshooting

EVPN not working

If after doing the following steps:

  1. Manually copy/paste the switch-basic-configuration to the devices.
  2. Run the playbook and push the generated configuration to the fabric.
  3. Login to a leaf device, for example, dc1-leaf1a and run the command show bgp evpn summary to view EVPN routes.

The following error message is shown:

dc1-leaf1a#show bgp evpn summ
% Not supported
dc1-leaf1a#

This is caused by AVD pushing the configuration line service routing protocols model multi-agent, which enables the multi-agent routing process supporting EVPN. This change requires a reboot of the device.


Last update: December 5, 2022